Bolted Flange Design 0.0.23a Documentation ASME BPVC Section VIII Division 1 Appendix 2 Project Information Description: Use Registered Project? Choose a Project: Project: Use Registered Equipment? Equipment: Choose an Equipment: Customer: Report Number: System of Units: International System of Units Imperial System of Units Process Information Fluid: Internal Design Temperature - Td: °C Internal Design Pressure - Pd: MPa Dimensions Flange Type: Figure 2-4(1) Figure 2-4(1) with hub Figure 2-4(1a) Figure 2-4(1a) with hub Figure 2-4(2)Figure 2-4(2a)Figure 2-4(3)Figure 2-4(3a)Figure 2-4(4)Figure 2-4(4a)Figure 2-4(4b)Figure 2-4(4c)Figure 2-4(5)Figure 2-4(6)Figure 2-4(6a)Figure 2-4(6b)Figure 2-4(7)Figure 2-4(8)Figure 2-4(8a)Figure 2-4(9)Figure 2-4(9a)Figure 2-4(10)Figure 2-4(10a) Flange Construction: Calculate as Loose or Integral? LooseIntegral Flange Outside Diameter - A: mm Flange Inside Diameter - B: mm Flange Thickness - t: mm Flange Nozzle Wall Thickness - tn: mm Thickness of Hub at Small End - g0: mm Thickness of Hub at Back of Flange - g1: mm Hub Length - h: mm Flange Face Outside Diameter - faceOD: mm Flange Face Inside Diameter - faceID: mm Lap Outside Diameter - Lod: mm Lap Flange Thickness - tl: mm Corrosion Allowance - corr: mm Use Corrosion Allowance in the Calculations? Joint Efficiency of the Pipe - Ep: 1.000.900.850.800.700.650.600.550.50 Use B1 instead of B if B < 20 * g1? Bolting Bolt Circle Diameter - varC: mm Bolt Unit Type: ImperialMetric Bolt Size: Bolt Nominal Diameter - BoltND: mm Bolt Root Area - BRArea: mm^2 Number of Bolts - NBolt: Material Properties Flange Material Name: Material Listing: Yield Strength at Design Temperature - FYDe: MPa Allowable Stress at Design Temperature - Sfo: MPa Allowable Stress at Ambient Temperature - Sfa: MPa Material Density - FMDensity: kg/m^3 P-Number Thickness - FMPnum: mm External Pressure Chart: UCS-66 Curve: Elastic Modulus at Operating Condition - Efo: MPa Elastic Modulus at Seating Condition - Efs: MPa Is the Material Normalized? Bolt Material Name: Material Listing: Yield Strength at Design Temperature - BYDe: MPa Allowable Stress at Design Temperature - BSfo: MPa Allowable Stress at Ambient Temperature - BSfa: MPa Material Density - BMDensity: kg/m^3 P Number Thickness - BMPnum: mm External Pressure Chart: UCS 66 Curve: Elastic Modulus at Operating Condition - BEfo: MPa Elastic Modulus at Seating Condition - BEfs: MPa Is the Material Normalized? Gasket Gasket Thickness - gt: mm Gasket Outside Diameter - GOD: mm Gasket Inside Diameter - GID: mm Use Gasket Database? Gasket Type: Gasket Factor - m: Gasket or Joint-Surface Unit Seating Load - gy: MPa Flange Facing Sketch (Table 2-5.2): 1a1b1c1d23456 Column from Table 2-5.2: III Flange Face Width - Nf: mm Serration Depth - sd: mm Nubbin Width - ws: mm Settings Show Factors Calculation? YesOnly the resultsNo Show Results with Toggle/Accordion Effect? YesNo Show Flange Image in the DOCX file? YesNo Calculate Reset Save tmin Bolted Flange Design ×